0 of 32 Questions completed
You have already completed the quiz before. Hence you can not start it again.
Quiz is loading…
You must sign in or sign up to start the quiz.
You must first complete the following:
0 of 32 Questions answered correctly
Time has elapsed
You have reached 0 of 0 point(s), (0)
Earned Point(s): 0 of 0, (0)
0 Essay(s) Pending (Possible Point(s): 0)
The maximum test pressure on an Amico medical gas outlet without the latch valve installed (rough-in only) is _____ PSI.
To rebuild/repair an Ohmeda compatible Amico latch valve assembly, you would need to order repair kit ______________ .
If the latch valve assembly is installed on an Amico oxygen outlet, the maximum test pressure is_____ PSI.
The part number for a Beacon Medaes Diamond 3 oxygen outlet finish assembly is _______________ .
If a Beacon Medaes Diamond 3 outlet is leaking with a quick connect adapter in place, the most
likely cause could be __________________ .
Amico DISS latch valve assemblies do not have o-ring seals on ________, _________, and
_________ medical gases.
Amico medical gas outlets should be inspected periodically, or at least ____________ .
Beacon Medaes outlets in high use areas should be inspected at least _________, and more frequently if outlets are used daily.
On Beacon Medaes Gemini/Diamond 3 outlets front bodies which are being rebuilt, new _________ must be used when reassembling the front body assemblies.
Beacon Medaes outlets elastomer seals may be lubricated sparingly with _____________ .
The minimum width on Becker KVT 2.000 series pumps valves prior to replacement is _________.
Bearings on Becker VTLF 200 pumps should be greased every _______ hours.
When a Becker DTLF pump lacks sufficient vacuum, a common possible cause could be ____________.
Intake filters on Becker VTLF 200 pumps should be checked and cleaned at least every _______.
Becker dry vane pump vane life is mostly dependant upon ___________________________.
Discharge filters on Becker KVT 3.140 pumps should be checked (and replaced if necessary) every ___________.
Vanes on a Becker VTLF400 pump should be checked for minimum width every ______________.
If carbon vanes on Becker DTLF pumps become stuck, they should be _______________.
Intake filters on Becker VT 4.10 pumps should be blown out _______.
The vacuum relief valve on Becker vacuum pumps must be periodically adjusted. When making this adjustment, a vacuum gauge should be placed on the inlet port, and the pump should be operated under no load for approximately ___________.
Busch MM vacuum pump gear oil should be changed every _____ hours or ____ years, using Busch approved gear oils, operating at standard conditions.
The inlet air filter on Busch MM vacuum pumps should be inspected _______ .
Rietschle C-VLR vacuum pumps should be operated at a maximum ambient temperature of ____ degrees centigrade.
The oil in a Rietschle C-VLR vacuum pump should be changed at _____ hours.
The coupling sprocket on a Rietschle C-VLR vacuum pump should be checked at least _______.
The correct gear oil level in a Busch MM vacuum pump should be ______________________________________ .
If a Busch MM vacuum pump drive motor is running and the pump is not running, the most probable cause is __________________________________ .
The Rietschle C-VLR vacuum pumps which have grease lubricated bearings on the B side are the __________ .
If a suction filter is installed on a Busch MM vacuum pump, it should filter foreign solid particles down to ____ microns or less.
On a Rietschle C-VLR vacuum pump, the allowable power supply voltage deviation from the motor data plate is _____ percent (without derating).
Busch R5 vacuum pump’s oil should be changed (after the first initial 100 hours of operation) every 3 to 4 months, or _____ to _____ hours, if not exposed to high heat operating conditions.
If a Busch R5 vacuum pump is running very noisily, one possible cause is _____________________ .